全国服务热线
18254766999(微信同号)
联系我们 CONTACT US
联系我们


嘉祥同信环卫设备有限公司

联系人:黄经理

电话:18254766999

网站:https://www.txhw88.com

地址:山东省济宁市嘉祥县

公司资讯您现在的位置:首页>新闻动态>公司资讯>二手洒水车水泵漏水如何处理?

二手洒水车水泵漏水如何处理?

来源:https://www.txhw88.com 日期:2020-04-17 发布人:同信环卫小编 浏览量:

[导读]:  二手洒水车水泵损坏,会造成吸力效果不好,洒水车压力不足,漏风等故障。一般都会用水泵来认为质量,其实喷灌泵的工作原理是机械密封,
  二手洒水车水泵损坏,会造成吸力效果不好,洒水车压力不足,漏风等故障。一般都会用水泵来认为质量,其实喷灌泵的工作原理是机械密封,在使用一段时间后对泵体零件进行一些必要的维护。下面是二手洒水车厂家介绍洒水车水泵相关信息!
  Second hand sprinkler pump damage, will cause suction effect is not good, sprinkler pressure is insufficient, air leakage and other failures. Generally speaking, water pump is used to consider the quality. In fact, the working principle of sprinkler pump is mechanical seal. After a period of use, some necessary maintenance is carried out for pump body parts. Below is the second-hand sprinkler manufacturers to introduce sprinkler pump information!
  洒水车水泵漏水处理方法——学习以下4点,从此不再担心水泵漏水!
二手洒水车
  Sprinkler water pump leakage treatment method - learn the following 4 points, from now on, no longer worry about water pump leakage!
  1、洒水车的水泵泵壳只要有轻微的裂口,可以用环氧树脂粘结,轴承座孔磨损过多,可以用镶嵌法修复,水泵壳体进气室如有麻点、沟槽或异常情况,可以用车床车削修复。如果泵壳爆裂严重,必须及时更换喷灌泵,以免耽误喷灌工作。
  1. As long as there is a slight crack in the water pump housing of the sprinkler, it can be bonded with epoxy resin, the bearing seat hole is worn too much, and it can be repaired by inlaying method, and if there are pockmarks, grooves or abnormal conditions in the air inlet chamber of the water pump housing, it can be repaired by turning the lathe. If the pump shell bursts seriously, the sprinkler pump must be replaced in time to avoid delaying the sprinkler work.
  2、洒水车泵轴腐蚀可采用挂锡点、凹补、再补圆的方法。
  2. For the corrosion of the pump shaft of the sprinkler, the method of hanging tin point, concave repair and re round repair can be adopted.
  3、水封磨损,橡胶水封老化、变形或损坏,水封弹簧受力或严重腐蚀应更换。
  3. The water seal shall be worn, the rubber water seal shall be aged, deformed or damaged, and the water seal spring shall be replaced in case of stress or serious corrosion.
  4. ,在维护之后,进行测试。具体方法是:用手更换V形带轮,应无堵塞现象,堵塞泵壳入口,然后将水放入叶轮操作室,转动泵轴,检查孔应无漏水现象。
  4. Finally, test after maintenance. The specific method is: replace the V-belt pulley by hand, and there should be no blockage. Block the inlet of the pump housing, then put the water into the impeller operating room, rotate the pump shaft, and check the hole to ensure there is no water leakage.
  了解了洒水车水泵漏水后的处理方法,让我们一起学习水泵故障的几种排除方法吧!
  Understand the sprinkler pump leakage after the treatment method, let's learn several troubleshooting methods of water pump together!
  1、检查洒水车网络系统是否漏水。
  1. Check the sprinkler network system for water leaks.
  2、检查洒水车网络上球阀开关位置是否正确。
  2. Check whether the switch position of the ball valve on the sprinkler network is correct.
  3、检查喷油泵或抽水机是否工作正常。
  3. Check whether the fuel injection pump or water pump works normally.
  4、检查滤芯是否有杂物堵塞滤芯。
  4. Check whether the filter element is blocked by sundries.
  4、如果是次使用洒水车,请检查水泵是否加水不够。
  4. If it is the first time to use the sprinkler, please check whether the water pump is not enough.
  5、洒水车抽水时,注意抽吸[即抽水管道长度大于7米]。
  5. When the sprinkler pumps water, pay attention to the suction [that is, the length of the pumping pipe is more than 7m].
  以上是二手洒水车厂家为大家介绍的相关内容,想要了解更多内容,欢迎访问网站:https://www.txhw88.com
  The above is the relevant content introduced by the second-hand sprinkler manufacturer. To learn more, please visit the website: https://www.txhw88.com
相关推荐:
相关新闻: