全国服务热线
18254766999(微信同号)
联系我们 CONTACT US
联系我们


嘉祥同信环卫设备有限公司

联系人:黄经理

电话:18254766999

网站:https://www.txhw88.com

地址:山东省济宁市嘉祥县

行业新闻您现在的位置:首页>新闻动态>行业新闻>经常使用的吸粪车怎么保养?

经常使用的吸粪车怎么保养?

来源:https://www.txhw88.com 日期:2020-04-28 发布人:同信环卫小编 浏览量:

[导读]:吸粪车是必备的环卫工具之一,是不可缺少的一部分,吸粪车真空泵油需经常补充和定期更换。一般每吸、排200-250次更新一次,废油从油气分离
吸粪车是必备的环卫工具之一,是不可缺少的一部分,吸粪车真空泵油需经常补充和定期更换。一般每吸、排200-250次更新一次,废油从油气分离器放油口排尽,从加油口加入新油,从以下的内容来讲述一下关于吸粪车的原理与保养维护方法吧。
The suction truck is one of the necessary sanitation tools and an indispensable part. The vacuum pump oil of the suction truck needs to be supplemented and replaced regularly. Generally, every 200-250 times of suction and discharge shall be renewed. Waste oil shall be discharged from the oil outlet of the oil gas separator, and new oil shall be added from the oil filler. The principle and maintenance method of the suction truck shall be described from the following contents.
疏通原理
Dredging principle
将管道疏通喷头通过高压胶管连接,并将喷头直接放在需要疏通的管道口,吸粪车的高压泵工作,吸粪车的喷头后方喷出的高压水所产生的反作用力,将喷头讯速向前推,并利用喷头前方和向后喷孔所产生的高压水射流迅速地将管道清洗干净,当收管器把喷头往回拉的同时,高压水流将管束内冲洗掉的污垢排出管外。
Connect the pipe dredge nozzle with high-pressure rubber pipe, and place the nozzle directly at the pipe mouth to be dredged. The high-pressure pump of the suction truck works. The reaction force generated by the high-pressure water sprayed from the rear of the nozzle of the suction truck pushes the nozzle forward at the speed of information, and cleans the pipe quickly by using the high-pressure water jet produced by the front and rear spray holes of the nozzle. When the receiver moves the nozzle back At the same time of pulling, the high-pressure water flow will discharge the washed dirt in the tube bundle out of the tube.
吸粪车维护保养
Maintenance of suction truck
过滤网应根据水质情况定期清洗,更好每日清洗一次。
The filter screen shall be cleaned regularly according to the water quality, preferably once a day.
高压泵内润滑油,初次使用 30~50 个小时更换一次,以后每 200 小时更换一次。
二手吸粪车
The lubricating oil in the high-pressure pump shall be replaced once every 30-50 hours of initial use and every 200 hours thereafter.
经常检查吸粪车运动部件及紧固件的连接情况,凡发现有松动,及时上紧,每天开机前检查滑块端面的防松螺钉是否松动,必须及时扳紧。定期检查柱塞轴向间隙,发现增大及时调整压紧螺套。
Frequently check the connection of the moving parts and fasteners of the manure suction truck. If any looseness is found, tighten it in time. Before starting the machine every day, focus on checking whether the anti loose screw on the end face of the slider is loose, and tighten it in time. Check the axial clearance of the plunger regularly, and adjust the compression screw sleeve in time if it is increased.
柱塞密封调整:柱塞密封处允许每分钟有1-5滴水珠,属正常情况,发现漏水较多时,要停机调整。先松开锁紧圆螺母,管道疏通吸粪车用专用扳手将钢套螺堵旋进到适当的紧度,然后用锁紧园锁紧。如发现漏水较多,钢套螺堵已无法再旋紧时,该处柱塞密封需要更换了。
Adjustment of plunger seal: 1-5 drops of water are allowed at the plunger seal every minute, which is normal. In case of more water leakage, stop the machine for adjustment. First, loosen the lock round nut, use a special wrench to screw the steel sleeve screw plug into the appropriate tightness, and then use the lock circle to lock it. If more water leakage is found and the steel sleeve plug can no longer be tightened, the plunger seal at this place needs to be replaced.
气温零下时,使用完毕后将设备内高压水排空,机器可空转 3~5 秒将高压泵内残留水排净。
When the temperature is below zero, drain the high-pressure water in the equipment after use, and the machine can idle for 3-5 seconds to drain the residual water in the high-pressure pump.
相关推荐:
相关新闻: